Kmc-controls CEP-4000 Series Uživatelský manuál stáhnout pdf (Strana 1)

CEP-4000 Series 1 Installation Guide

Installation Guide

Mounting

The CEP-4000 series are designed to mount on a

standard 1/2 in. (13 mm) diameter shaft or (using the

optional HFO-0011 adaptor) on a 3/8 in. (9.5 mm)

shaft.

Standard Instructions

1. Ensure that the damper can move freely through

its entire range of motion. Fix any binding before

installing the CEP-4000.

2. Slide the CEP-4000 directly onto the 1/2 in.

diameter damper shaft. The shaft must extend a

minimum of 1-3/4 in. from the mounting surface.

(For a 3/8 in. shaft, see the HFO-0011 Adaptor

section below.)

3. Place the non-rotation bracket (supplied) on the

non-rotation tab.

4. Aachthenon-rotationbrackettothemounting

surface using (2) #8 or #10 self-tapping screws

(not included).

5. Checkthatthestandos(ontheanti-rotation

bracket) provide a 1/8-inch air gap behind the

unit (see illustration).

6. Torque the two 5/16-18 setscrews to 75–85 in-lbs.

7. Mount the factory-calibrated, matching, SSE

series sensor horizontally to maintain calibration

atzeroairow.

HFO-0011 Adaptor

1. Mount the CEP-4000 series actuator over the 3/8

in. shaft.

2. Slide the HFO-0011 over the shaft into the drive

hub of the actuator.

3. Align the adaptor slots with the setscrews.

4. Partially tighten the setscrews.

5. Continue with step 2 under the Standard

Instructions section above.

NOTE: See also the CEP-4995 Universal

Replacement section on page 4 if installing

that replacement model.

Mounting 1

Standard Instructions 1

HFO-0011 Adaptor 1

Wiring 2

Adjustments and Calibration 3

Rotation Setup and Override 3

CEP-4995 Universal Replacement 4

Maintenance 4

More Information 4

CEP-4000 Side View

HFO-0011 Adaptor

Analog Electronic VAV Flow Controller-Actuators

CEP-4000 Series

NOTE: For information about connections and

usage with newer CTE-5202 thermostats,

see the CTE-5202 Applications Guide.

1 2 3 4

Shrnutí obsahu

Strany 1 - Installation Guide

CEP-4000 Series 1 Installation GuideInstallation GuideMountingThe CEP-4000 series are designed to mount on a standard 1/2 in. (13 mm) diameter shaft

Strany 2 - CAUTION

CEP-4000 Series 2 Installation GuideWiring1. Connect the CEP to an SSE sensor: A. Terminal 1 to sensor terminal 1.B. Terminal 2 to sensor termina

Strany 3 - Adjustments and Calibration

CEP-4000 Series 3 Installation GuideRotation Setup and OverrideIf desired, the rotation direction can be reversed by swapping the red and blue motor

Strany 4 - More Information

Komentáře k této Příručce

Žádné komentáře

Kmc-controls CEP-4000 Series Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Kmc-controls CEP-4000 Series. KMC Controls CEP-4000 Series User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Kmc-controls CEP-4000 Series Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Kmc-controls CEP-4000 Series. KMC Controls CEP-4000 Series User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Senzory Kmc-controls CEP-4000 Series