Kmc-controls CTE-5201-16 Uživatelský manuál stáhnout pdf

CTE-5201 1 Installation and Operation Guide

Mounting the Thermostat

1. Ifthethermostatis

lockedonthebackplate,

turnthetwohexscrews

(inthetwo outermost

holes)inthebackplate

CLOCKWISEuntilthey(just)clearthecover.

Swingthethermostatupandawayfromthe

backplatetoremoveit.

CAUTION

To prevent damage to the board, do not insert

a screwdriver into any holes other than the two

outermost holes. To prevent mounting screw heads

Installation and Operation Guide

Electronic Room Thermostat (Modular)

CTE-5201

Mounting

Rough-in Preparation

For optimum temperature sensor performance, the

thermostat must be mounted on an interior wall

and away from heat sources, sunlight, windows,

air vents, and air circulation obstructions (e.g.,

curtains, furniture).

Completerough-inwiringpriortoinstallation:

• Routethecablefromthethermostatlocationto

theactuatortowhichitwillconnect.SeeWiring

on page 2.

•

Ifneeded,installtheHMO-1161mounting

backplate.SeeAdditional Information on page 4.

from touching the circuit board in the thermostat, use

only the mounting screws supplied by KMC Controls.

Using other screws may damage the thermostat. Do

not turn screws in farther than necessary to remove

the cover.

2. Routethecablethroughthebackplate.

3. Withthehexscrewstowardthe

oor,fastenthebackplatetothe

outletboxwiththesuppliedscrews.

(Thebackplatemountsdirectlyon

vertical2x4inchboxes,butre-

quiresanHMO-1161wallmounting

plateforhorizontalor4x4boxes.)

4. Insertthemodularendofthecable

intothejackofthethermostat.

5. Placethetopofthethermostatoverthetopof

themountingbaseandswingitdownoverthe

hexscrewbrackets.Becarefulnottopinchthe

wiring.

6.

Backthehexscrewsoutofthebackplatebrackets

(counterclockwise) untiltheyengagethether-

mostatandholditinplace.

E F

RJ-12

Modular

Connector

Pin 6

Pin 1

Mounting 1

Rough-in Preparation 1

Mounting the Thermostat 1

Wiring 2

Modular to Modular (HSO-22xx Cable) 2

Modular to Leads (HSO-5012 Cable) 2

Operation 3

Turn On Backlight 3

Change Setpoint 3

Start Unoccupied Mode 3

Toggle Between °F and °C 3

Conﬁguration 3

Changing Defaults 3

MAX 3

MIN 3

F/C 3

UNOCC 3

PROP 4

INT 4

Calibration (Temperature Offset) 4

Maintenance 4

Additional Information 4

Pin 1 and 6 Pin 2 and 5 Pin 3 Pin 4

N/C Common Supply

(14–19VDC)

Output

(2–10VDC)*

*0VDCduringUnoccupiedOmodewhentemperaturestays

above50°F

3.25

in.

83

5.16

in.

116

0.88

in.

22

0.38

in.

10

2.58

in.

66

3.25

in.

83

1 2 3 4

Shrnutí obsahu

Strany 1 - CAUTION

CTE-5201 1 Installation and Operation GuideMounting the Thermostat1. Ifthethermostatislockedonthebackplate,turnthetwohexscrews(in

Strany 2 - 3/8"

CTE-5201 2 Installation and Operation GuideWiringModular to Modular (HSO-22xx Cable)UseHSO-22xxcablestoconnectthether-mostattoMEP-4x42a

Strany 3 - Operation

CTE-5201 3 Installation and Operation GuideConﬁgurationOperationChanging DefaultsThefactorydefaultseingsare:• Setpoint(Default):70F•

Strany 4 - Additional Information

CTE-5201 4 Installation and Operation GuideMaintenanceRemovedustasnecessaryfromholesintopandboom.Cleanthedisplaywithso,dampclo

Komentáře k této Příručce

Žádné komentáře

Kmc-controls CTE-5201-16 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Kmc-controls CTE-5201-16. KMC Controls CTE-5201-16 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Senzory Kmc-controls CTE-5201-16